Honed Concrete Around Pool Areas vs Exposed Aggregate
Deciding between honed concrete around pool areas and exposed aggregate comes down to three things: how the surface looks, how it feels under bare feet, and how much upkeep you want. Both are poured in place, and both can work well beside water when they are finished and sealed with care. Here is how they compare, using a honed pool surround we poured in Adelaide as a real example.

Every surround we pour is wet laid and finished on-site as one continuous surface. It is not dropped in as precast sections that can shift and crack at the joins, which matters around a pool where people walk barefoot every day.
What is honed concrete?
Honed concrete is concrete that is ground back with a machine after it has hardened, removing the top layer to leave a smooth, matte surface. Depending on how deep it is ground, you see fine sand and cut stone through the face. It gives a clean, modern look, close to a stone paver but poured as one slab.
Exposed aggregate works the other way. The top layer of cement paste is washed off while the concrete is still fresh, so whole stones sit slightly proud of the surface. That gives more texture underfoot and a speckled look, and the colour depends on the stone blend. Our guide to exposed aggregate colours in Adelaide shows real mixes we have laid.
Honed concrete vs exposed aggregate pool surrounds: side by side
This table compares the two finishes on the points that matter most around a pool.
| Factor | Honed concrete | Exposed aggregate |
|---|---|---|
| Look | Smooth, matte and even. Light mixes like Vanilla Spice give a soft, sandy tone. | Speckled stone texture. The colour comes from the stone blend and base. |
| Feel underfoot | Flat and smooth, comfortable for bare feet. | Textured. You can feel the stones under your feet. |
| Slip resistance | Depends on how it is ground and what sealer is used. Ask for a tested result. | Varies with the size and shape of the stone and the sealer used. Ask for a tested result. |
| Heat | Colour matters more than finish. Lighter colours absorb less sun than dark ones. | Same rule. A light stone blend stays more comfortable than a dark one. |
| Upkeep | Smooth face is easy to sweep and hose down. | Sweep or pressure clean regularly and clear leaves to avoid staining. |
| Sealing | Can be sealed. Talk through the sealer and any slip resistance additive first. | Can be sealed for a wet look. Sealers need recoating over time. |
Slip resistance around pools: what the standard covers
As of October 2026, AS 4586-2013, Slip resistance classification of new pedestrian surface materials, is the Australian Standard that provides a means of classifying pedestrian surface materials by their frictional characteristics. Its test methods can measure those characteristics in wet or dry conditions. The AS 4586-2013 summary on Codehub lists it as replacing AS/NZS 4586:2004, with an amendment issued in 2017.
Two points in that summary matter for a pool. The standard classifies new surface materials, and it does not account for in-service wear. So a test result tells you how a finish performed when new, not how it will feel after years of use.
Sealers matter too. The Dulux Avista exposed aggregate sealer datasheet states that “application of sealer can lower slip resistance” and that slip resistance additives are available. Before you lock in a finish and a sealer, ask for the tested slip resistance classification and how the sealer affects it.
Rules change and vary by council, so check with your local council before you start. We can help you work out what’s needed.
Our 40 MPa Vanilla Spice honed pool surround
The surround in our main photo was poured with 40 MPa Vanilla Spice honed concrete provided by Premix Concrete. When we shared it, we called it a “perfect beach vibe around your pool for the summer”. The light, warm cream colour is the reason: it reads more like sand than grey slab.
The 40 MPa figure is the strength grade of the concrete mix. The photo was taken mid-job, with timber bracing still across the pool, and it shows the surround wrapping around the pool as one continuous surface.
Drainage, coping and sealing choices
Falls away from the pool and the house
A pool surround has to shed water. In our prep stage we excavate, set the drainage falls so water runs away from both the pool and the house, and place the reinforcement before the pour. Water left sitting on a surround is a slip risk and can wash dirt back towards the pool.
The coping junction
Where the surround meets the coping is the line people notice first. We handle pool surrounds, coping and resurfacing, so the junction between them is planned as part of the same job rather than left to chance. Talk to us at the site visit about how you want that edge to look.
Sealing choices
Sealing is a choice between looks and grip, and it needs upkeep. For its own exposed aggregate sealer, the Dulux datasheet suggests recoating approximately every 2 years, with actual life depending on use and environment. It also lists pool chlorine as having “no visual effect” on the sealer.
Every product is different, so check the datasheet for whatever sealer goes down. Our FAQ on what exposed aggregate sealing is covers the basics.

Which finish suits your pool?
There is no single right answer. Use this as a quick guide:
- Choose honed if you want a smooth, modern look, a soft feel for bare feet and a light, even colour.
- Choose exposed aggregate if you want more texture underfoot, a speckled stone look, or a surround that matches an exposed aggregate driveway or path.
- Either way, settle the slip resistance, the falls and the sealer before the pour, not after.

“Great experience from start to finish. Very professional, reliable and easy to communicate with. The concreting work was completed efficiently and to a high standard.”
– Pan Penny, Google review
Get a quote for your pool surround
If you are weighing up honed concrete around pool areas against exposed aggregate, the right choice depends on the look you want, how it feels underfoot, and the slip resistance and sealing you settle on. We offer free, no-obligation quotes, and the same crew looks after your job from the first site visit to the final finish. Call 0429 426 991 or request a quote online, and see more on our pool concreting in Adelaide page.